Morso 2110 Operations Instructions download pdf (Page 7)

1312

The secondary air is injected into the ﬂue gases both above and in front of the ﬁre resulting in

a cleaner, more efﬁcient combustion process. The supply of secondary air is ﬁxed open and is

not adjustable.

For extra safety, your stove has been ﬁtted with a removable handle. When not in use the handle

can be stored using the lug behind the right leg of the stove.

2.2 Lighting and loading intervals

When ﬁrst lighting the stove, a large volume of air is needed. When the stove is cold, you should

leave the door open an inch or two for the ﬁrst few minutes and open the primary air

supply completely. While the door is open, do not leave the stove unattended.

To form a reasonable bed of ash on the ﬂoor of the stove, you should use 5-6 inches thickness

(2-4 pound) of dry kindling at the initial lighting. Always maintain a 1-1.5 inch (2-3 cm) layer of

ash on the ﬂoor of the combustion chamber at all other times.

Step-by-step procedure

1. The air supply must be fully open.

2. Light the ﬁre. An ember bed will quickly be formed by lighting with ﬁrelighters, morsø kindling

bags or 7-10 pieces of twisted paper under the dry kindling wood (see above).

3. After lighting, partially close the doors, leaving them open an inch or two to allow in plenty

of combustion air.

4. When the chimney is warmed through after 5-10 minutes, the doors should be closed. A

suitable ember bed will be formed after a further 15-20 minutes.

5. When ready to reload, use a poker to spread the ember across the ﬁrebox ﬂoor, bringing

plenty towards the front of the stove.

6. Lay three pieces of wood (see dimensions above) onto the embers. Leave half an inch (1 cm)

or more between each piece. When using 10 inches (25 cm) logs, place the ends of your logs

towards the opening, but not too close to the front.

In principle

Your stove is ﬁtted with Primary and Secondary air inlets.

Primary Air is controlled using the lever situated under the ash lip of the stove. Moving the

control lever into a downward position will open the air inlet and will allow a supply of preheated

air to enter the ﬁrebox via the ‘airwash’ system situated inside the stove and the above glass.

Secondary Air is right to the ﬁrebox using the specially designed bafﬂe at the back of the ﬁrebox

Do not for any reason attempt to increase the ﬁring of your heater by altering the air

control adjustment range outlined in these directions.

Warning: Fireplace stoves must never be left unattended with doors open.

If the doors are left partly open, gas and ﬂame may be drawn out of the ﬁreplace stove

opening, creating risks from both ﬁre and smoke. We recommend you to ﬁt a smoke detector

in the room where the stove is installed.

DO NOT OVERFIRE THIS HEATER. Overﬁring may cause a house ﬁre, or can result in

permanent damage to the stove. If any part of the stove glows, you are overﬁring.

The maximum recommended weight of wood fuel per load is 2.5 kg/h/5.5Ibs (approx 3 split logs).

Under normal ﬁring, the average ﬂue temperature in the stove pipe, measured 20 cm above the

stove, is approx. 300° C (550°F). The maximum ﬂue temperature in the stove pipe must not exceed

450° C (750°F). If the ﬂue temperature exceeds 450°C (750°F), it is considered as over ﬁring and

may cause premature wear and tear of the stove.

To help gauge the correct running temperature of your stove, we recommend you use the Morsø

Flue Gas Thermometer (part # 62901200). The Flue Gas Thermometer magnetically attaches onto

the stove pipe approx 20 cm (8”) above the stove’s top plate and measures the surface temperature

of the stove pipe. Please see your authorized Morsø Dealer for availability.

Draft conditions

If smoke or fumes come out of your stove when lightning up and reloading, or if the ﬁre simply

will not respond, a poor draft is almost certainly to blame. (In a very few cases, there may be

insufﬁcient fresh air getting into the room - see installation advice above). Take advice from your

stove supplier on how best to upgrade your ﬂue system to improve draft.

Rules of woodburning

If you want less heat, put fewer logs on the stove and reduce the amount of air. It is still important

to maintain a good layer of embers.

Less heat - less wood - less air

Greater heat - more wood - more air

Soot deposits will settle on the glass if the stove is run too slowly or if your wood is

not well seasoned.

7. Close the door. Leave the primary air supply fully open.

8. After a few minutes, and adjust the primary air supply to suit your heating requirements.

9. Anticipate each refueling, remembering to add a modest layer of wood while there are still

plenty of live embers, Repeat steps 5-8.

1 2 3 4 5 6 7 8 9 10 11

Comments to this Manuals

No comments

Morso 2110 Operations Instructions Page 7

Comments to this Manuals

Related products and manuals for Cookers Morso 2110